Race Master / Alpha-X Insert Block Assembly

  • 699 SEK

PLEASE NOTE: If  you are ordering a holster or an insert block for a CZ TS checkmate or  CZ TS Orange, please contact us first with a picture of your

I lager.

Betala som du vill
Payment with Visa Payment with Mastercard Payment with Payson Payment with Swish Payment with Svea
Payson - Faktura, Delbetalning, Kort, Konto, Bank
Swish - till 123 650 9111 (Skanna QR kod)
DHL - Fri frakt från 1000kr (annars 89kr)
DHL Paket (för företag) - 190kr
Självhämtning Helsingborg - 0kr

PLEASE NOTE: If  you are ordering a holster or an insert block for a CZ TS checkmate or  CZ TS Orange, please contact us first with a picture of your trigger  guard area. CZ seem to be using two styles of frames for these pistols  ,and without seeing your gun, we will not know which insert model you  need. 

US Patent No. 8720754.

Note: Both the Race Master holsters and the Alpha-X holsters use the same insert blocks.

The Race Master Holster utilizes an efficient and easy system to allow  shooters to switch their holster from one gun type to another by means  of changing the Insert Block Assembly. This switch is fast and easy and  can be done in less than a minute, and without losing any of the  holster's adjustments or settings.

The Insert Block Assembly includes:
1. The Locking Block (gun specific).
2. The Sliding Lock, assembled (gun specific).
3. The safety lever, assembled.
4. The internal magnetic activation system, assembled.

The Insert block grips the pistol only on the front end of the trigger  guard, and a very precise fit is required in that area. In some cases  some light modifications to the Insert Block may be required.

Should you need to dismantle your insert block for some fitting, follow these steps:
1. Remove the insert block from the holster by removing the two small M4 screws from the back of the holster.
2. Using a punch and hammer, push the two steel pins from the front of  the block towards the back (push from the side with the gun type  engraved). These pins may be tight.
3. Once the pins are out, the plastic wedge holding the 2nd magnet will  come out. Make sure the magnet does not fall out the part. It is usually  held snugly it its pocket.
4. Use a marker to make a dot on the top of the magnet which is embedded  in the slide lock. This will make it easy for you to ensure that you  reassemble it with the correct side up. Most likely it will fall out or  you will want to remove it while fitting the slide lock.
5. To remove the slide lock from the block, unscrew the M3 screw visible  from the back of the block – and then slide the slide lock upwards and  out through the window in the block – passed the safety lever, which  must be in the unlocked position.

To reassemble- reverse your steps.

The Race-Master Holster Insert Blocks are design to be used in either RH or LH holsters. The same insert works for both.



Read the following instructions carefully before using this holster or Insert Block:

  • Never holster a loaded firearm without first engaging its safety.
  • Check periodically to ensure your safety is functioning correctly.
  • Never disengage the safety of the firearm until well clear of the holster and the muzzle is pointing down range.
  • Make sure you are fully familiar with the correct use, and  adjustment of your DAA Holster before attempting to use it with a loaded  firearm.
  • Make sure that you have the correct holster/Insert model for your type of firearm.
  • Do not use a holster that is unsuited to your firearm, as that  could result in unreliable retention or release which could lead to a  fatal accident.
  • Never use a trigger shoe or a widened trigger with this holster.
  • Double check that the retention and release work well, particularly if any modifications have been made to your firearm.
  • Care must be taken to ensure the gun is placed properly when  returned to the holster. It if it is not positioned correctly, it will  not be held securely and may fall out.
  • Never holster the gun quickly or with force, as that increases the chance of making contact with the trigger.
  • Any adjustment or modification to the holster design may render it unsafe or cause malfunction.
  • Take care that the firearm is not dislodged or knocked when  holstered, particularly when the holster’s safety lever is unlocked. As  this holster has no muzzle support, take care that the muzzle of the gun  is not bumped upwards, as this may dislodge the gun from the holster
  • Keep your fingers well clear of the trigger when holstering and drawing the firearm.
  • The holster should be locked when running or jumping with a  holstered gun, or you should keep your hand on the gun’s grip to prevent  it accidentally falling.
  • Handling a loaded firearm, and drawing it from a holster is  inherently dangerous. You do so entirely at your own risk and  responsibility.  
  • Liability is limited only to the replacement of this holster or  parts thereof. No additional warranties are expressed or implied by the  manufacturer or the distributors.